Compare Commercial Roofing Bids in Portland

A legitimate commercial roof quote names the system, the scope, every drain and penetration, the exclusions and the warranty. Bids only compare when every bidder prices that same scope, so send one pre-bid scope sheet before you ask for numbers. And before you score anyone, check the bidder’s Oregon CCB commercial endorsement. That is how to compare commercial roofing bids in Portland.
Updated: October 2026
Here is an illustrative case, not a real job. You manage an older three-story retail building with a tired flat roof. Three bids land on your desk in the same week. Bid A prices the work by the square foot. Bid B prices it by drain count and penetrations. Bid C skips the tear-off and proposes a recover over the old membrane.
The totals sit far apart, and no two of them describe the same work. So which one is cheapest? You cannot tell. Neither can the owner who will ask you to justify the pick.
Most property managers in that spot take the lowest number or the most confident salesperson. Both feel reasonable. Both are how a building ends up with a leak in November or a warranty that never got registered.
The scope is yours to set, and this guide shows how to compare commercial roofing bids in Portland the way an asset manager would, even with three bids already in your inbox.
Why Don’t Your Three Commercial Roof Bids Match?

Your bids don’t match because each roofer filled the gaps in your request with their own assumptions. One assumed a tear-off, another a recover; one counted square feet, another counted drains.
What Is the Difference Between an Estimate, a Quote and a Bid?
An estimate is a rough price, often based on a quick look or an aerial measurement. A quote is a fixed price for a defined scope, valid for a stated period. A bid is a quote priced against a scope you wrote, in competition with other contractors.
For a roofing bid comparison, you want bids, because only bids share a scope that came from you. An estimate tells you whether the project fits the budget, not who to hire.
Why Does One Roofer Price by Square Foot and Another by Drain Count?
Roofers price by different units because commercial roof cost lives in different places. The field membrane scales with square footage. Drains, scuppers, curbs and pipe penetrations each need their own flashing and labor, so some roofers price them one by one.
The main commercial roof cost factors are roof area, penetrations, parapet length, insulation thickness, layers to remove and access. A downtown building that needs a street crane costs more to roof than a Hillsboro warehouse with a loading dock.
Neither method is wrong. Trouble starts when one bid folds every penetration into a square-foot rate and another lists them separately. The fix is to choose one structure for every bidder: a square-foot rate for the field, plus a unit price for each drain, scupper and penetration.
What Should a Commercial Roof Quote Include?

A commercial roof quote should name the roof system and membrane thickness, the tear-off or recover scope, insulation, every drain and penetration, and the flashing. It should also list exclusions, unit prices for hidden deck repair, the warranty, the schedule and how long the price holds.
Use this table as your yardstick for any commercial roofing quote in Portland. Mark each line on each bid as present, vague or missing. A vague line is a question to send back in writing; a missing line is a future change order.
| Quote element | What it must state | What you lose if it is missing |
|---|---|---|
| Roof system | Membrane type (TPO, EPDM, PVC or modified bitumen), thickness in mils, attachment method | Proof that two bids price the same product |
| Tear-off or recover | Layers removed, or the existing roof left in place, and why | A fair reason one bid is far cheaper than another |
| Insulation and cover board | Insulation type, thickness, target R-value, cover board type, tapered areas | Energy code compliance and drainage on flat spots |
| Drains, scuppers, penetrations | Count of each, and whether priced per unit or in a lump sum | A way to check what the price covers |
| Flashing and edge metal | Parapets, curbs, coping and edge metal: replaced or reused | Protection against old metal leaking at new seams |
| Ratings and permit | Wind uplift rating, fire rating, who pulls the permit | Assurance the roof meets code and insurer requirements |
| Hidden deck repair | Unit price per square foot of deck and per board of wet insulation | A cap on change orders after tear-off |
| Exclusions | Everything the bidder will not do or pay for | Warning of extras before you sign |
| Warranty | Manufacturer warranty type and term, workmanship term, who backs each | Knowing who pays when the roof fails |
| Schedule and validity | Start window, duration, work hours, date the price expires | Control over tenant disruption and price drift |
The Roof System: Membrane, Thickness and Attachment
The quote should name one membrane, its thickness and how it attaches. Two bids that name different systems are not comparable until you ask why.
The four commercial flat roof systems on Portland bids price differently. TPO is a white, heat-welded sheet common on retail and warehouse roofs. EPDM is black rubber with taped or glued seams. PVC is heat-welded and resists grease, which matters over restaurant exhaust. Modified bitumen is multi-ply asphalt, common on older mixed-use buildings.
Thickness matters as much as the membrane name. A 45-mil and a 60-mil sheet of the same membrane are different products at different prices. Every bid should name the same system, or explain in writing why it doesn’t.
Tear-Off, Recover, Deck and Insulation
The quote must say whether the old roof comes off or stays, and what insulation goes on. These lines explain most of the price gap between bids that look alike on paper.
A recover installs a new membrane over the existing roof, which costs less and skips the disposal. It only works when the old roof is dry and the deck is sound, and building codes generally bar a recover once a roof already carries two layers. A tear-off strips everything to the deck, so the roofer can find and replace wet insulation and damaged decking. That is why a recover bid and a tear-off bid can never sit on the same line of your comparison.
Insulation is the other half of commercial roof design. State the thickness, the target R-value and any tapered insulation that moves water toward the drains. A cover board protects the insulation and helps the roof reach its wind uplift rating. Oregon sets a minimum for commercial roofs too. A fact sheet from the Polyisocyanurate Insulation Manufacturers Association summarizing the 2025 Oregon Energy Efficiency Specialty Code lists R-30 continuous insulation for low-slope commercial roofs in Climate Zone 4, and says it applies to roof replacements on existing buildings, not only new construction.
Are Drains, Flashing and Penetrations Priced Per Unit or Lump Sum?
Both are acceptable, provided the quote states how many of each item the price covers. Roof drainage systems matter here, because a flat roof that ponds after long rain ages early. A lump sum works when it lists every drain, scupper, curb and pipe. A per-unit price works better when the count could change once the old roof comes off.
Exclusions and Unit Prices for Hidden Deck Repair
Every commercial quote should list what it excludes and price hidden deck repair per unit. Rotted deck and wet insulation are the usual surprises, and the unit price is what stops change orders from growing unchecked.
Common exclusions include HVAC disconnects, electrical work, permit fees, engineering and after-hours labor. Older Portland buildings may also need asbestos testing of old mastic before tear-off, so the quote should say who arranges and pays for it.
Is Your Commercial Roofer Licensed, Bonded and Insured for This Job?
A roofer can hold a valid Oregon license and still not be licensed for your building. The Oregon Construction Contractors Board licenses commercial and residential work under separate endorsements, each with its own bond and liability minimum. Check that before you spend an hour scoring any bid.
The Oregon CCB requires a commercial endorsement for work on commercial structures. A contractor who holds both endorsements carries two bonds and one liability policy, per the CCB Endorsement Chart. The commercial minimums vary by endorsement level. The chart lists, for example, a $55,000 bond with $1 million aggregate insurance for Commercial Specialty Contractor Level 1, and a $25,000 bond with $500,000 per occurrence for Level 2.
Bond amounts also changed recently. Oregon House Bill 2922 (2023) raised every CCB minimum bond by $5,000, effective January 1, 2024. A bond on file is not enough; it has to be current at today’s amount. A bidder who fails this filter is out before you ask anyone to re-price anything.
How Do You Check a CCB Commercial Endorsement?
Search the bidder’s CCB number or business name in the CCB online license lookup. The result shows license status, endorsement type, bond and insurance on file. The whole check takes under a minute per bidder.
These are the Oregon roofing contractor requirements to confirm in the record:
- The license status reads active, not lapsed or suspended.
- The endorsement is commercial, not residential only.
- The bond and liability insurance on file are current.
- The business name on the license matches the name on the bid.
Geek Roofing holds CCB #235209, and you can check it the same way you check anyone else. If your property sits in Vancouver, Washington licenses contractors through its Department of Labor and Industries instead.
What Do the Bond and the Insurance Certificate Actually Protect?
The CCB bond is a limited fund you can claim against if the contractor breaks the contract or Oregon construction law. General liability insurance pays for damage the crew causes to the building, tenants or neighbors. Neither one guarantees the quality of the roof.
A bonded, insured commercial roofer in Portland should send a certificate of insurance straight from their insurance agent. Ask that it name the owner and the management company as additional insured, with policy dates that cover the whole project.
What Do Commercial Roof Warranties Actually Cover?

Commercial roof warranties come in two kinds. A manufacturer warranty covers the membrane, and sometimes the whole roof system, against product defects. A workmanship warranty from the roofer covers installation errors. Neither one is insurance: storm damage, other trades’ work and skipped maintenance usually fall outside both.
That last point catches property managers most often. Wind damage, a dropped tool from an HVAC crew or a clogged drain that ponds for months belongs to your property insurance or maintenance budget. Ask each bidder which warranty they offer, who backs it and what voids it.
Manufacturer Warranty vs Workmanship Warranty
A manufacturer warranty is backed by the company that made the membrane. A workmanship warranty is backed only by the roofing contractor. The first survives if the roofer closes; the second does not.
Manufacturer warranties split further. A material-only warranty replaces defective membrane but leaves the labor to you. A system warranty covers membrane, insulation and accessories from one manufacturer, and usually requires a manufacturer-approved installer plus a final inspection. When a bid promises a system warranty, ask whether the bidder is approved by that manufacturer to issue it. For how manufacturer certification works on the residential side, see GAF Master Elite requirements in Portland.
How Long Do Flat Roof Warranties Last?
Flat roof warranty terms depend on the manufacturer, the system and the membrane thickness. Longer terms usually require thicker membrane, more insulation and stricter inspections. Workmanship terms are set by each contractor and vary widely.
Manufacturer terms run from about five years to 35. GAF offers commercial guarantees of 10 to 35 years, depending on the system and the contractor’s certification, and Carlisle SynTec offers terms of up to 30 years. Only certified contractors can issue the longest ones.
On your scope sheet and scorecard, compare warranty terms only between bids that name the same system and thickness. A longer term attached to a thinner membrane is a question to ask, not a bonus to celebrate.
Send One Pre-Bid Scope Sheet and Get Three Comparable Bids

A pre-bid scope sheet is a one-page document you send every qualified bidder before anyone prices the job. It fixes the decisions that make bids drift apart: tear-off or recover, insulation target, price units, warranty and work hours. Bids priced on one sheet come back comparable.
Roofers fill a blank request with their own preferences. A written scope replaces those preferences with your decisions, and gives you a document to hand the owner when they ask how the contractor was chosen.
What Goes on the Scope Sheet
Copy this list into a one-page document and fill in each line. Where you have not decided, ask bidders to price both options as separate lines.
- Property: address, building use, number of stories, occupied or vacant.
- Existing roof: system, known layers, approximate age, known leak spots, past repairs.
- Scope: full tear-off to the deck, or recover. If undecided, price both separately.
- New system: membrane type, thickness and attachment. Alternates allowed only after the base spec is priced.
- Insulation: target R-value, tapered insulation at ponding areas, cover board type.
- Drains, scuppers and penetrations: your count of each, priced per unit.
- Flashing and metal: parapets, curbs, coping and edge metal replaced, not reused.
- Hidden conditions: unit price per square foot of deck and per board of wet insulation.
- Ratings and permit: wind uplift and fire rating required, permit pulled by the contractor.
- Warranty: manufacturer warranty type and term wanted, plus workmanship term.
- Site rules: work hours, access points, staging area, crane limits, odor and noise rules.
- Bid format: one price form for all, due date, price valid for a stated number of days, questions in writing only.
Why Run One Shared Walkthrough With Every Bidder?
One walkthrough with every bidder present means everyone sees the same roof, hears the same answers and prices the same conditions. It also replaces three separate roof visits with one.
Treat it as your commercial roof inspection checklist in motion: walk bidders past every drain and scupper, the ponding areas, soft spots underfoot and each rooftop unit, then show them the ceilings where tenants reported leaks.
Answer questions on the spot, then send the same answers to every bidder in writing. If one bidder spots a condition others missed, such as wet insulation near a curb, add it to the sheet for all. When a shared visit is impossible, send everyone the same photo set instead. That keeps a property manager roof inspection in Portland fair, even across different visit days.
Tenant Hours, Access and Schedule Rules
Write tenant rules into the sheet before anyone bids, because they change the price. After-hours work, crane windows and odor control all cost money. A bid that ignores them will either re-price later or put you at odds with your leases.
A restaurant on Alberta Street needs its exhaust fans protected. A downtown retail building may need a street crane, which means a city permit and a fixed window.
Portland’s wet season belongs on the schedule too. Ask each bidder how they keep the building dry overnight during a tear-off, and what happens to the schedule when rain sets in for a week.
How to Compare Commercial Roofing Bids Side by Side
To compare commercial roofing bids, confirm that every bid prices the same scope, normalize any that don’t, then score each one on the same criteria. Price comes last, once all three bids describe the same roof.
Normalize Every Bid to the Same Scope First
Normalizing means adjusting each bid until it prices the same work. Add any missing items using that bidder’s own unit prices, or ask the bidder to re-price the gap in writing. Never fill a gap with your own guess.
Residential bids normalize more easily (see what a Portland roof replacement costs for a home); a commercial flat roof estimate in Portland adds drains, insulation targets and tenant conditions, so you adjust line by line.
Two adjustments cover most cases. Ask a lump-sum bidder for a line breakdown, and ask a recover bidder for tear-off pricing as an alternate. A bidder who refuses to re-price has told you something useful.
What Does the Price Leave Out?
Two checks are pass or fail: the bidder holds a CCB commercial endorsement, and the bid prices your scope sheet. Everything else gets weighed against the normalized price.
Read each bid for who pays when something goes wrong: the warranty behind the roof, the schedule your tenants will live with and the exclusions you will pay for separately. A longer system warranty backed by the manufacturer shifts risk away from you. An exclusions list you have read line by line means no surprise invoices. A higher price can be the better buy when it removes one of those risks.
Illustrative Example: Three Bids, One Scorecard
The table below is an illustrative example, not a real job or real client. It shows how three bids on one building score once you put them side by side against the scope sheet.
| Criterion | Bid A | Bid B | Bid C |
|---|---|---|---|
| Prices the scope sheet as written | Yes | Yes, after re-pricing | No, recover only |
| System and thickness named | Yes | Yes | Thickness missing |
| Deck repair unit price | Yes | Yes | No |
| Manufacturer and workmanship warranty stated | Both, material-only | Both, system warranty | Workmanship only |
| Schedule fits tenant hours | Yes | Partly, weekday days only | Not stated |
| CCB commercial endorsement and insurance certificate | Verified | Verified | Residential endorsement only |
| Normalized price | Middle | Highest | Lowest, not comparable |
Bid C has the lowest total, but it fails the license check and prices only a recover, so it leaves the list. Bid A and Bid B both qualify. Bid B costs more but carries the manufacturer’s system warranty. Bid A wins here because tenants get evening work and the extra cost of B does not pay for itself on this building. That reasoning fits in one paragraph to the owner, and every line of it can be checked.
Low-Bid Red Flags and the Final Check Before You Sign

Treat a low bid as a question, not a bargain. A bid that fails the license check or won’t price your sheet is out on its own. Eliminate any other bid that fails two or more of the checks below, then take the finalists to a scoped site visit. This is the last gate in how to compare commercial roofing bids in Portland.
Most low commercial roofing bid red flags trace back to an earlier step in this guide. These are the ones to run before you sign:
- The bid fails your scope sheet, the CCB check or the deck repair rate (see the sections above).
- The price expires within days, which pushes you to sign before you can compare.
- The deposit covers most of the contract before work starts. A deposit for special-order material is normal; one that funds the whole job shifts the risk to you.
Is the Low Bid Missing Scope or Saving Money?
Ask the low bidder to confirm in writing that the price covers every line of your scope sheet. If they confirm and the number holds, the savings may be real. If the number moves, the low bid was missing scope.
Real savings happen: a roofer in a slow month or with a crew nearby can price the same roof lower. That is why cheap roofing bids should raise red flags but not disqualify a bidder outright.
When to Bring in a Second Site Visit
Bring the finalists back for a second, scoped visit when their bids still differ after normalizing, or when one bidder flagged a condition the others missed. Core cuts or a moisture scan settle wet insulation and deck questions with evidence instead of opinion.
For general vetting beyond the commercial specifics here, use these questions to ask a roofing contractor. They work for any finalist, on any roof.
If you want a qualified bidder in that process, Geek Roofing’s commercial roofing services cover TPO, EPDM, PVC and modified bitumen roofs across Portland, Beaverton, Hillsboro and Clackamas, under CCB #235209.
Frequently asked questions
How long does a commercial roof replacement take?
A commercial roof replacement takes days to a few weeks, depending on roof area, tear-off and weather. Roof size, the number of old layers and rain delays set the schedule. Ask each bidder for a start window, a duration and a rain plan in writing, so you can compare them on your scorecard.
How long is a commercial roofing estimate valid?
Every quote should state its own expiry date, so ask for it in writing. Material prices and crew schedules move, which is why validity belongs on the bid. A price that expires within days is a pressure tactic, not a courtesy (see the red flags above).
Is TPO or EPDM better for a commercial flat roof?
Neither wins everywhere, so ask each bidder to justify their system for your roof. Over restaurant exhaust, PVC often enters the conversation because it resists grease. Compare any two systems at equal thickness, and judge the reasoning, not the label.
Does the age of my roof change which system I should ask for?
Yes, mainly through the number of layers already on the roof. Two layers generally rule out a recover. Repair history matters too: a roof patched often in the same spot usually hides wet insulation, which points to a tear-off bid.
Still have questions?
Reach out and we’ll cover these and more:
- What does a commercial roof assessment from Geek Roofing involve, and who attends?
- Can you price my scope sheet as written, with alternates for tear-off and recover?
- How do you schedule work around tenants and Portland’s wet season?


